Media added by Mike65

Navigation

Browse albums
8/2/16 I had to modify the factory radio mounting bracket to fit the 80's era AM/FM stereo radio.

8/2/16 I had to modify the factory radio mounting bracket to fit the 80's era AM/FM stereo radio.

  • 0
  • 0
8/1/16 Drilled all the spot weld holes in the l/s long floor & reworked the front section that overlaps the toe board for a better fit.

8/1/16 Drilled all the spot weld holes in the l/s long floor & reworked the front section that overlaps the toe board for a better fit.

  • 0
  • 0
7/31/16 Welded in the l/s toe board patch & drilled the spot weld holes in the l/s long floor pan did another test fit.

7/31/16 Welded in the l/s toe board patch & drilled the spot weld holes in the l/s long floor pan did another test fit.

  • 0
  • 0
7/30/16 Trimmed & reformed the upper section of the l/s toe board & drilled the spot weld holes.

7/30/16 Trimmed & reformed the upper section of the l/s toe board & drilled the spot weld holes.

  • 0
  • 0
7/29/16 Fitting l/s full floor, so I know how much to cut off the toe board patch.

7/29/16 Fitting l/s full floor, so I know how much to cut off the toe board patch.

  • 0
  • 0
7/27/16 Welded in the l/s outer torque box.

7/27/16 Welded in the l/s outer torque box.

  • 0
  • 0
7/27/16 Finished welding in the l/s inner torque box.

7/27/16 Finished welding in the l/s inner torque box.

  • 0
  • 0
7/24/16 Welded in the l/s floor support, & started welding in the l/s inner torque box.

7/24/16 Welded in the l/s floor support, & started welding in the l/s inner torque box.

  • 0
  • 0
7/20/16 Test fit the l/s outer torque box.

7/20/16 Test fit the l/s outer torque box.

  • 0
  • 0
7/20/16 Test fit the l/s floor support & l/s inner torque box.

7/20/16 Test fit the l/s floor support & l/s inner torque box.

  • 0
  • 0
7/1/16 Ground down the welds on the l/s frame patches & test fit the l/s floor support.

7/1/16 Ground down the welds on the l/s frame patches & test fit the l/s floor support.

  • 0
  • 0
7/10/16 I finished welding in the l/s cowl side panel patch.

7/10/16 I finished welding in the l/s cowl side panel patch.

  • 0
  • 0
7/9/16 Welded in the frame patches on the rear section of the l/s frame rail.

7/9/16 Welded in the frame patches on the rear section of the l/s frame rail.

  • 0
  • 0
7/9/16 Started welding in the l/s cowl side panel patch.

7/9/16 Started welding in the l/s cowl side panel patch.

  • 0
  • 0
6/29/16 re-test fitting l/s cowl patch panel.

6/29/16 re-test fitting l/s cowl patch panel.

  • 0
  • 0
6/29/16 test fitting l/s floor support.

6/29/16 test fitting l/s floor support.

  • 0
  • 0
6/27/16 Cut away the remainder of the rotted section of the l/s frame rail.

6/27/16 Cut away the remainder of the rotted section of the l/s frame rail.

  • 0
  • 0
6/26/16 made patch for l/s cowl side panel.

6/26/16 made patch for l/s cowl side panel.

  • 0
  • 0
6/25/16 I cut out 1/2 of the l/s front floor support.

6/25/16 I cut out 1/2 of the l/s front floor support.

  • 0
  • 0
6/25/16 I cut out the rusted area around the fresh air vent opening.

6/25/16 I cut out the rusted area around the fresh air vent opening.

  • 0
  • 0
6/15/16 Removed remainder of the l/s outer torque box.

6/15/16 Removed remainder of the l/s outer torque box.

  • 0
  • 0
6/12/16 Cut out remainder of l/s torque box.

6/12/16 Cut out remainder of l/s torque box.

  • 0
  • 0
6/12/16 Shelby convertible lower side scoops installed.

6/12/16 Shelby convertible lower side scoops installed.

  • 0
  • 0
Added Shelby convertible lower side scoops.

Added Shelby convertible lower side scoops.

  • 0
  • 0