Media added by Mike65

Navigation

Browse albums
9/5/16 Assembled steering column.

9/5/16 Assembled steering column.

  • 0
  • 0
9/4/16 All the pieces to the steering column are painted & awaiting assembly.

9/4/16 All the pieces to the steering column are painted & awaiting assembly.

  • 0
  • 0
9/3/16 Painted the steering column tube, & the 2 turn signal switch housing pieces.

9/3/16 Painted the steering column tube, & the 2 turn signal switch housing pieces.

  • 0
  • 0
9/2/16 Completed disassembly of Mustang steering column for cleaning & parts replacement.

9/2/16 Completed disassembly of Mustang steering column for cleaning & parts replacement.

  • 0
  • 0
8/30/16 Stripping paint off the radiator support.

8/30/16 Stripping paint off the radiator support.

  • 0
  • 0
8/27/16 Cleaned the undercoating off the shock tower, frame rail, firewall, & most of the rear inner fender panel.

8/27/16 Cleaned the undercoating off the shock tower, frame rail, firewall, & most of the rear inner fender panel.

  • 0
  • 0
8/26/16 Starting to clean inner fender panels, shock towers, & frame rail of surface rust, & undercoating.

8/26/16 Starting to clean inner fender panels, shock towers, & frame rail of surface rust, & undercoating.

  • 0
  • 0
8/23/16 Removed the suspension pieces from the l/s.

8/23/16 Removed the suspension pieces from the l/s.

  • 0
  • 0
8/21/16 Removed all the suspension components from the r/s.

8/21/16 Removed all the suspension components from the r/s.

  • 0
  • 0
8/19/16 Welded in the l/s door post patches.

8/19/16 Welded in the l/s door post patches.

  • 0
  • 0
8/17/16 Made 2 patches for the l/s door post & the lower part of the windshield post just below the upper door hinge.

8/17/16 Made 2 patches for the l/s door post & the lower part of the windshield post just below the upper door hinge.

  • 0
  • 0
8/17/16 Cut out rust through spot & prepped for patches.

8/17/16 Cut out rust through spot & prepped for patches.

  • 0
  • 0
8/17/16 Rust through spot just below l/s upper door hinge.

8/17/16 Rust through spot just below l/s upper door hinge.

  • 0
  • 0
8/16/16 Welded in the patch on the l/s rear part of the l/s inner cowl panel.

8/16/16 Welded in the patch on the l/s rear part of the l/s inner cowl panel.

  • 0
  • 0
8/10/16 Welded in patch l/s lower rear of l/s door post.

8/10/16 Welded in patch l/s lower rear of l/s door post.

  • 0
  • 0
8/10/16 Welded in patch l/s outer cowl side panel.

8/10/16 Welded in patch l/s outer cowl side panel.

  • 0
  • 0
8/9/16 Cut out rust through spot in l/s outer cowl panel.

8/9/16 Cut out rust through spot in l/s outer cowl panel.

  • 0
  • 0
8/8/16 Cut out the rear section of the l/s inner cowl panel that was starting to rust through where it is welded to the door post.

8/8/16 Cut out the rear section of the l/s inner cowl panel that was starting to rust through where it is welded to the door post.

  • 0
  • 0
8/8/16 Cut out a small piece from the lower rear section of the l/s door post that had some pin holes in it.

8/8/16 Cut out a small piece from the lower rear section of the l/s door post that had some pin holes in it.

  • 0
  • 0
8/7/16 Tested the fit of the Monte Carlo bar.

8/7/16 Tested the fit of the Monte Carlo bar.

  • 0
  • 0
8/6/16 Bolted the drivers side seat back in.

8/6/16 Bolted the drivers side seat back in.

  • 0
  • 0
8/6/16 I welded in the seat platform

8/6/16 I welded in the seat platform

  • 0
  • 0
8/5/16 I finished welding in the l/s long floor & started fitting the seat platform.

8/5/16 I finished welding in the l/s long floor & started fitting the seat platform.

  • 0
  • 0
8/3/16 I started welding in the l/s long floor until I ran out of welding wire.

8/3/16 I started welding in the l/s long floor until I ran out of welding wire.

  • 0
  • 0