Side exhaust

[Wicked One]

I am looking for pics of side exhaust from under the car. I want to see how it is routed and the ground clearance. Gonna fab up something and want to see how they did it.

Thanks guys.

 

[BlackStang14]

dont get it....
I live up state and I have already ripped it off MANY times... I can get those pictures for you tomorrow.. It goes straight back a little past the pumpkin then turns out and down out the side... hooks up into the floor pan in the back and has mufflers (glass packs) after the midpipe... First month I got the exhaust I wore down the clamps on the tips completely sparking everywhere.. You can see it in my You tube videos...

Tips are a pain in the ass and ever speed bump you will hitt they lie maybe a little more then a inch off the groung barely...
Heres the pictures from one of my problems...

How its held up in the back... (the broken one... I had to reweld everything thanks to queens...)

Right before they come out the sides..

This is how low I am...

See how it was shaved off...

Well I wouldnt reccomend it for new york... I worry about the exhaust everywhere.. and have had to fix it many many times...

 

[Wicked One]

Holy crap man, Thanks. looks like I am sticking with the rear exit. Maybe I'll make it dump out behind the rear tires.

 

[BlackStang14]

Holy crap man, Thanks. looks like I am sticking with the rear exit. Maybe I'll make it dump out behind the rear tires.

I will say if you are a good fabricator, you could make it work... I will take a couple full pictures for you once I get the car back up... It could be made to work but it would take time.. Sorry its not what you expected... You also live in rougher enviroment then me...

 

[Wicked One]

Yeah, down here the roads plain SUCK!!!. Thanks again man, Looking to change it up a bit. Not gonna change the exhaust yet, have to get my Supercharger, & cams first.

 

[RedMOsesSC]

Did you say Cams

I have a hard time with ground clearance with my rear exit exhuast, side exit would be destroyed quickly here in the city.

 

[Wicked One]

Yes I did!!! But I have to get a Blower grind, so I am not gonna spend 800$ on a set just to remove them in a few months. Have to make some calls and see if I can get a really nice setup. I am going for torque, not max hp.

 

[RedMOsesSC]

They say that the stock cams work great with blowers. Theres no need to swap your cams out now for a blower grind because it wont do much for you, your better of putting that money twrds the SC and doing cams down the road when you have maxed out your set up and are looking to turn up the boost.

 

[irishpwr46]

make some dumps for right inside the rear wheels. that way when you do a burnout your exhaust is pushing the tire smoke out away from the car and making it look a lot better

 

[RedMOsesSC]

Ooooooooow dumps, thats Slutty!!! They dont look as good as side exhuast but they look much more mean n nasty. You planning on getting a new rear bumper? There a new Edge Roush in LIC that i see all the time, its really nice but it has side exhuast and rear exhuast, that just kills the whole vibe for me.

 

[Wicked One]

If I do the dumps I will get the cervinis rear bumper. But I like the idea of the dumps aiming outward, that can be done with ease.

Now all I need is a lift. I might make some sort of tire block to put the car on. I saw some that are cool but cost a butt load.

 

[BlackStang14]

Not hard you could do it just do like 2 pieces.... mufflers then you custom dumps...

 

[Wicked One]

Hey what with the new Name??? Had me scratching my ass for a minute.

For the dumps, I was gonna used my flowmasters and just hack off the ends and weld them to the new pipe setup. I go to CT on the weekends so it's gonna wait till monday.

Dentist tomorrow,, re-paint the boats outdrive, set up boat slip and launch the focker. Then home late sat for Sundays cruise or Mahopac car show.

 

[boostingwild]

Hey what with the new Name??? Had me scratching my ass for a minute.

For the dumps, I was gonna used my flowmasters and just hack off the ends and weld them to the new pipe setup. I go to CT on the weekends so it's gonna wait till monday.

Dentist tomorrow,, re-paint the boats outdrive, set up boat slip and launch the focker. Then home late sat for Sundays cruise or Mahopac car show.

do you know how to weld?

 

[BlackStang14]

Hey what with the new Name??? Had me scratching my ass for a minute.

For the dumps, I was gonna used my flowmasters and just hack off the ends and weld them to the new pipe setup. I go to CT on the weekends so it's gonna wait till monday.

Dentist tomorrow,, re-paint the boats outdrive, set up boat slip and launch the focker. Then home late sat for Sundays cruise or Mahopac car show.

Ha me and mike were messing around... More or less mike was messing with me lol.... CT has alot of blue oval guys... cool crew... You got alot going on lol... Let me know if you want me to swing by and help out...

 

[BlackStang14]

do you know how to weld?

lol welding is easy even if you suck just get good with a grinder lol... The question is more or less if you have a welder...

 

[Wicked One]

Yeah I can weld, and Yes I have a welder. Gonna take a look at it when I get home later today or monday. Thanks for the offer, I might take you up on it.